Performance of Al2O3 particle reinforced glass-based seals in planar solid oxide fuel cells

Glass-based materials are usually considered as excellent seals for jointing adjacent components in planar solid oxide fuel cells, but the uncontrollable crystallization in the glass may cause delamination and micro-cracks in such seals. To solve this problem, Al2O3 ceramic particles were added to a BaO–CaO–Al2O3–B2O3–SiO2 glass system to reduce negative effects caused by crystalline phase on the gas tightness and the joint strength in the seals. At an operating temperature of 750 °C, the glass-based seals with 20 wt% Al2O3 addition (GA80) exhibited extremely low leakage rates (~0.002 sccm/cm under an input gas pressure of 13.6 kPa) and higher shear strength (3.31 MPa). The Al2O3 ceramic addition and the crystalline phase BaAl2Si2O8 reinforced the glass matrix. Further thermal cycle analyses indicated that leakage rates for the GA80 seals remained at around 0.0025 sccm/cm after 10 thermal cycles, which was consistent with minor microstructural change and good interface bonding. Single cell testing with of GA80 seals was performed and the results demonstrated stable electrochemical performance through 6 thermal cycles at an open circuit voltage of 1.16–1.18 V, as well as a power density above 546 mW/cm2 at a current density of 925 mA/cm2. These results showed the high thermal cycle stability of the glass/Al2O3 composite seals in intermediate temperature planar solid oxide fuel cells.     

Construction,structure and photocatalysis of janus nanofiber modified by g-C3N4 nanosheets heterostructure photocatalysts

The construction of photocatalyst with gradient band structure is guided by the principle of band gap engineering. Rational structural design is advanced and applied to construct a new-typed peculiarly structural and functional carbon-based [TiO₂/C]//[Bi₂WO₆/C] Janus nanofiber modified by g-C₃N₄ nanosheets heterostructure photocatalyst (denoted as TB-JgHP). The flexible carbon-based [TiO₂/C]//[Bi₂WO₆/C] Janus nanofiber with one side responding to ultraviolet light and the other capturing visible light is fabricated by conjugate electrospinning, and then g-C₃N₄ nanosheets are uniformly grown in-situ on the surface of the Janus nanofibers by using gas-solid reaction via gasification of urea. The optimized TB-JgHP possesses remarkable hydrogen evolution efficiency (17.48 mmol h⁻¹ g⁻¹) and methylene blue degradation rate (99.2%) under simulated sunlight illumination for 100 min, demonstrating prominent dual-functional characteristics. The enhanced photocatalytic performance benefits from the unique Janus structure as well as the synergistic effects among the triple heterostructures of TiO₂ and Bi₂WO₆, g-C₃N₄ and TiO₂, g-C₃N₄ and Bi₂WO₆. The formation of gradient band structure among heterostructures is more conducive to the multi-step separation of photo-induced electron-hole pairs and more effective absorption of light. Further, flexible self-standing carbon-based photocatalysts not only have outstanding electron transport performance, but also are easy to separate from solution with preeminent recyclable stability. Based on a series of characterization techniques, it is further proved that TB-JgHP has higher carrier separation efficiency than the counterpart contrast samples. The formation mechanism of TB-JgHP is proposed, and the construction technique is established. The design philosophy and construction technique presented in this work pave a new avenue for research and development of other heterostructure photocatalysts.     

A comprehensive survey on computer vision based concepts,methodologies, analysis and applications for automatic gun/knife detection

The ability to detect gun and gun held in hand or other body parts is a typical human skill. The same problem presents an imperative task for computer vision system. Automatic observer independent detection of hand held gun or gun held in the other body part, whether it is visible or concealed, provides enhance security in vulnerable places and initiates appropriate action there. Compare to the automatic object detection systems, automatic detection of gun has very few successful attempts. In the present scope of this paper, we present an extensive survey on automatic detection of gun and define a taxonomy for this particular detection system. We also describe the inherent difficulties related with this problem. In this survey of published papers, we examine different approaches used in state-of-the-art attempts and compare performances of these approaches. Finally, this paper concludes pointing to the possible research gaps in related fields.     

Thermal shock response behaviour of carbon fibre reinforced silicon carbide matrix composites prepared by chemical vapour infiltration at different heating rates

The present work investigated the effects of thermal cycles in air on the tensile properties of a two-dimensional carbon fibre reinforced silicon carbide composite (2D C/SiC) prepared by chemical vapour infiltration at different heating rates. The composite was exposed to different cycles of thermal shock between 20 °C and 1300 °C in air. The damage mechanisms were investigated by AE online monitoring and fractured morphology offline analysis. The tensile strength of 2D-C/SiC decreases with increasing thermal cycles. However, the modulus only decrease within 40 cycles. Due to oxidation, with the decrease in heating rate, the residual properties of the material decrease more obviously. Meanwhile, the results of AE online monitoring and fracture analysis show that the matrix damage is more serious at higher heating rate and that more delamination occours in tensile fractures. The above results indicate that for the thermal shock of 2D C/SiC composites in air, oxidative damage plays a key role in the residual properties.     

Control of viscous fingering and mixing in miscible displacements with time-dependent rates

In miscible displacements encountered in enhanced oil recovery processes, the unfavorable viscosity contrast between injected solvent and oil usually leads to viscous fingering (VF), a hydrodynamic instability which may result in a lower sweep efficiency and oil recovery. This phenomenon can be observed in a wide range of flows in subsurface porous media. This study examined a simple cyclic time-dependent displacement rate and its effects on the onset and longer development of VF. It is found that such varying displacement rate can either stabilize or destabilize VF, depending on the cycle period, amplitude, and displacement scenarios. The most important mechanism is that such time-dependent rate can effectively change the competition between convection (destabilizing effect) and dispersion (stabilizing effect). This is different from the widely used constant injection rate where the flow instability is actually determined by the Peclet number and mobility contrast for a given scenario. This study therefore provided a new aspect to control VF, either enhance or reduce, with low additional costs. It is therefore both scientifically and practically important for a wide range of flows in subsurface porous media. © 2017 American Institute of Chemical Engineers AIChE J, 65: 360–371, 2019     

Multiple Empirical Kernel Learning with Majority Projection for imbalanced problems

Traditional Multiple Empirical Kernel Learning (MEKL) expands the expressions of the sample and brings better classification ability by using different empirical kernels to map the original data space into multiple kernel spaces. To make MEKL suit for the imbalanced problems, this paper introduces a weight matrix and a regularization term into MEKL. The weight matrix assigns high misclassification cost to the minority samples to balanced misclassification cost between minority and majority class. The regularization term named Majority Projection (MP) is used to make the classification hyperplane fit the distribution shape of majority samples and enlarge the between-class distance of minority and majority class. The contributions of this work are: (i) assigning high cost to minority samples to deal with imbalanced problems, (ii) introducing a new regularization term to concern the property of data distribution, (iii) and modifying the original PAC-Bayes bound to test the error upper bound of MEKL-MP. Through analyzing the experimental results, the proposed MEKL-MP is well suited to the imbalanced problems and has lower generalization risk in accordance with the value of PAC-Bayes bound.     

A hybrid multiple feature construction approach for classification using Genetic Programming

The purpose of feature construction is to create new higher-level features from original ones. Genetic Programming (GP) was usually employed to perform feature construction tasks due to its flexible representation. Filter-based approach and wrapper-based approach are two commonly used feature construction approaches according to their different evaluation functions. In this paper, we propose a hybrid feature construction approach using genetic programming (Hybrid-GPFC) that combines filter’s fitness function and wrapper’s fitness function, and propose a multiple feature construction method that stores top excellent individuals during a single GP run. Experiments on ten datasets show that our proposed multiple feature construction method (Fcm) can achieve better (or equivalent) classification performance than the single feature construction method (Fcs), and our Hybrid-GPFC can obtain better classification performance than filter-based feature construction approaches (Filter-GPFC) and wrapper-based feature construction approaches (Wrapper-GPFC) in most cases. Further investigations on combinations of constructed features and original features show that constructed features augmented with original features do not improve the classification performance comparing with constructed features only. The comparisons with three state-of-art methods show that in majority of cases, our proposed hybrid multiple feature construction approach can achieve better classification performance.     

基于时间延迟的多类型维修与经济生产批量联合优化研究

针对目前未能较好的综合考虑多维修类型与经济生产批量联合优化的问题，首先考虑多类型维修关系，基于时间延迟理论求出故障和缺陷次数的表达式；其次，在此基础上，综合考虑生产费用和维修费用的基础上，构建了多类型维修和经济生产批量联合优化模型，以单位时间内总费用最小为优化目标，获得最优检查间隔期和经济生产批量；最后，通过算例分析验证了模型的有效性，说明了第一类缺陷检查次数的多少对费用和经济生产批量影响不大。     

A PV installation framework concerning electricity variable rates

This paper assesses building integrated photovoltaic (BIPV) installation parameters based on the profit generated by a photovoltaic system. It takes into consideration a home building case study and it investigates its monthly energy demand based on a specific location and a typical occupancy. The capability of a photovoltaic (PV) system to generate more profit occurs when solar intensity is maximum while the electric energy price is at its highest rate. The paper traces a framework that encompasses different aspects such as energy demand, energy price, and solar intensity. This framework identifies profit alternatives according to different installation parameters. A tool that predicts a PV installation hourly electric energy production is developed. The profit generated is simulated for home buildings located in Beirut (Lebanon) and Xihua (China), both at 33.8° latitude north. The paper highlights a new approach for BIPV installations, taking into account weather conditions, energy demand, and electric energy utility rates.